当前位置：
上海鼎振仪器设备有限公司 >
产品中心 >
蒸汽喷射试验箱 > DIN EN ISO16925涂料和清漆.涂层耐压力水喷射的测定LTA1
DIN EN ISO16925涂料和清漆.涂层耐压力水喷射的测定LTA1
| 产品型号： |
LTA1 |
|
|
| 所 在 地： |
上海嘉定区 |
| 更新日期： |
2024-04-16 |
蒸汽喷射试验箱 LTA1 Steam Jet Testers LTA1
WALTER Cleaningsystems developped an interbranch procedure in
cooperation with Daimler with which the paint adhesion on painted plastic
components can be tested.
The most important factor is to apply the exact volume flow with well-defined
pressures and constant temperature onto the surface.
A further step of development is the compliance with the DIN ISO 16925
standard which guarantees a cross-border standardization of the testing
method.
Due to our worldwide servicing all units are maintained depending on their
state of wear and are brought into a technically perfect condition. The
calibration carried out by a Walter technician and the traceability to general
standards guarantee a worldwide comparability. We thereby also certify
nozzles conforming to standards and train the operators in how to carry out
the tests.
Due to continuous developments we also fulfil the testing specifications of the
following manufacturers
WALTER Cleaningsystems 与戴姆勒公司合作开发了一种测试程序，可以测试
涂漆塑料部件上的油漆附着力。
*重要的因素是将具有明确定义的压力和恒定温度的精确体积流量应用于表
面。
进一步的发展是符合 DIN ISO 16925 标准，该标准保证了测试方法的跨境标准
化。
由于我们的全球服务，所有装置都根据其磨损状态进行维护，并使其处于技术
上完美的状态。 由 Walter 技术人员执行的校准以及对一般标准的可追溯性保证
了全球的可比性。 因此，我们还对符合标准的喷嘴进行认证，并培训操作员如
何进行测试。
Frame:
base frame with 4 guide rollers
Boiler container with heating 1 x 9,0 kW
Spraying booth:
• dimensions wx d x h: 1138 x 730 x 2240 mm
for 1 x test piece approx. 150 x 300 mm
• testing angle 90° - 45° - 30°, +/- 2°
• booth door with inspection glass
• exhaust Ø 102 mm connection piece
• discharge with dirt filter
Possible options:
• horizontal sliding unit
• Volvo – sweeping action
• exhaust fan
• laser pointer
• flow meter
• testing equipment for metering in litres
• nozzle and plug-in nipple according to nonstandard norms
Technical Data: 技术参数
| Flow rate |
15 l/min |
P max.
|
30 – 150 bar adjustable via external pressure
regulating valve (water via by-pass, thus less delivery
volume) |
| Motor |
N 6,5 kW |
| Voltage |
400 V |
| Plug |
CEE 32 amp., 5-pole |
Nozzle distance
|
0 – 450 mm nozzle with adjusting mechanism in
2 directions |
For testing according to the following specifications:
符合标准
• DIN EN ISO 16925:2014-06
• DBL 5416
• Ford BO 160-04
• GM 9531
• Volvo STD 423-0015
• VW PV 1503
• BMW AA-0136
• Renault D 252018
• PSA D 255376
• MAN M 3022
• KIA Hyundai MS210-07
• DAF KEUR00824 -848
• NISSAN M0141
